🔨 Home Speaker Build — Cut & Assembly Guide

Everything measured, nothing guessed. Two 2-way ported bookshelf speakers, ¾" MDF, external 11.5"H × 9.5"W × 12"D, tuned ~45 Hz. Total parts:

One sheet of 4×8 ft ¾" MDF cuts both cabinets (incl. bracing) with generous scrap. Port length was recalculated and the box deepened so the 2" port genuinely fits — the first draft had a port that was longer than the box was deep.

1 · Panel cut list — one cabinet (make TWO of each)

PieceSize (¾" MDF)QtyNotes
Front baffle9.5 × 11.522 driver cutouts + flush recess
Back panel9.5 × 11.52+ 2" port hole, + terminal hole
Sides10.5 × 104internal depth × internal height
Top / Bottom8 × 10.54internal width × internal depth
Brace (optional)~8 × 321 horizontal strut per cabinet

All sizes in inches. Butt construction: sides & top/bottom sit between the front and back faces.

2 · Sheet layout — how to cut the 4×8 sheet

48" wide × 96" long — ¾" MDF (one sheet, both cabinets)
Front B 9.5×11.5
Front A 9.5×11.5
Back A 9.5×11.5
Back B 9.5×11.5
Sides A/B & Tops
remaining sheet
Cut the four 9.5×11.5 faces first, then the 8 sides (10.5×10) and 4 top/bottoms (8×10.5) from the rest — everything fits with scrap left over.

3 · Front baffle layout (each baffle)

Woofer centered ~4.75" from the sides, its center ~5" down (top edge of the box). Tweeter directly above, tweeter center ~4.75" in and ~1" from the top. Driver cutout diameters: use the flange/template that ships with each driver; recess the baffle a router-depth (~½–¾ the flange) so flanges sit flush. Keep woofer/tweeter center-to-center ≈ 5.5".

4 · Assembly — step by step

1

Mark & cut all panels per the cut list. Rip one cabinet's worth at a time so identical pairs stay matched.

2

Rout driver recesses on the two front baffles and drill the port (2") and terminal (for binding posts) holes on the two backs.

3

Dry-fit one box with clamps — check all 6 panels seat flush (sides & top/bottom inside the front/back faces).

4

Glue & screw the box: run a bead of wood glue on every butt edge, clamp, and add a few screws per joint. Glue all edges — no gaps.

5

Install the brace across the internal width (half-box height) and clamp until dry. Also seal every interior seam with extra glue.

6

Assemble the crossover on a small board (inductor + caps + resistor per channel) and solder the wiring: amp terminals → crossover → drivers. Keep the iron-core-free inductor clear of the woofer magnet.

7

Mount the port (2" × ~8", rear) and fit the binding post terminal. Run speaker wire inside, then screw the drivers into the recessed baffle flanges.

8

Add damping — loosely fill the interior with polyester fiber (no packing; the port must stay clear). Finish: seal seams and paint/vinyl, add rubber feet.

9

Wire up & test — match +/− on every driver. Play a slow sweep; double-check no buzz or port chuff at normal volume.

5 · Parts quick-reference

PartModel / #Qty
Woofer · Dayton WebDC160-8 (295-305)2
Tweeter · Dayton DC28F-8275-0702
Inductor 0.60 mH air-core257-8182
Cap 10 µF027-4282
Cap 3.3 µF027-4202
Resistor 8 Ω 10 W006-22
Port kit 2" flared268-3482
Binding post pair091-3402
MDF 3/4" 4×8Home Depot1
Shortcut: if you'd rather not solder the discrete components, a prebuilt Dayton XO2W-2.5K (260-142, $31.69 ea) replaces inductor+2 caps+resistor per speaker — just wire amp→XO2W→drivers. Slightly dearer but foolproof.